Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Garden Oaks Homeowners
Most chimney trouble in Garden Oaks starts at the top. A missing cap lets rain, squirrels, and nesting birds straight into the flue. A cracked crown lets water soak the masonry below it, and by the time you notice a stain on the ceiling, the repair has grown well past the crown. Our technicians have up to 14 years of experience reading exactly those failures, and we install caps and crowns from professional-trade brands like Gelco and Famco rather than the flimsy hardware-store versions that fail in a season or two. We offer same-day service when the schedule allows, and every job starts with a flat-price quote you approve before we book. Call (844) 299-4971 and we’ll take a look at what your cap and crown actually need.
What Our Chimney Cap & Crown Service Includes
Cap Installation
A chimney cap is the fitted cover that sits on top of the flue, and it’s the cheapest protection your chimney will ever get. You need one if your flue is open to the sky, which is the case on plenty of older Garden Oaks homes where the original cap rusted away or was never fitted. We measure the flue opening, then install a stainless or copper cap sized to that specific flue so it seats properly instead of rattling loose in a gust. The cap keeps rain, leaves, and animals out of the flue and keeps sparks off your roof.

Cap Replacement
Caps don’t last forever. Rust-through, bent mesh, or a cap that’s come loose in high wind are all reasons to replace rather than patch. You need a replacement when the mesh is torn, the top is rusted into holes, or the cap no longer sits square on the flue. We pull the old unit, check the flue tile underneath for damage the failing cap may have let in, and fit a new Gelco or Famco cap that’s built for the weather here. The old cap comes away with us.

Crown Repair
The crown is the concrete or mortar slab on top of the chimney that sheds water away from the masonry below. Hairline cracks are common and mostly harmless; wider cracks that let water sit on top of the chimney are not. You need crown repair when water is finding its way into the brick, when the crown has pulled away from the flue, or when pieces of mortar are dropping onto the roof. We remove the failed section, rebuild it to shed water properly, and check the flue tile for the water damage a bad crown often causes quietly underneath.

Crown Coating
Crown coating is a flexible sealant applied over a crown that’s still structurally sound but showing its age. You need it when the crown has surface cracks or is starting to chalk and crumble but hasn’t failed outright. Coating is far less expensive than a rebuild and buys years of service when the crown is a good candidate. We apply crown coating only when the crown passes inspection; if it’s already broken through, we tell you straight and quote a rebuild instead of coating a failed crown to make the invoice simpler.
Multi-Flue Cap
A multi-flue cap covers several flue openings under one single unit, which is what most larger Garden Oaks chimneys have. You need one when the original multi-flue cap is rusted through or the mesh has been torn by an animal, or when a previous job fitted a single-flue cap over a chimney that actually has more than one flue. A proper multi-flue cap protects every flue under one cover and looks cleaner up there. We measure the whole chimney top, match the cap to the footprint, and confirm it doesn’t block ventilation between the flues.
Custom Cap
Some chimneys don’t take a stock cap. Oversized flues, unusual stack layouts, and chimneys with a decorative shroud all need a made-to-fit unit. You need a custom cap when a standard size won’t seat properly, which is more common in older homes where the chimney was built by hand to whatever dimensions the mason worked out. We take careful measurements of the flue and crown, then have a custom cap fabricated to fit exactly. We work with Olympia Chimney products for custom configurations, and the result seals the flue without blocking draft.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We install Gelco caps and Famco caps because both brands are built for the purpose, not adapted from some other product. We know where Gelco’s stainless models hold up and where a Famco unit is the better call on a wide chimney top. When the job calls for a custom fit, we work with Olympia Chimney, a maker whose configurations handle the oddball flues we run into across Garden Oaks and Oak Forest.
We also work with HeatShield on the flue-repair side of cap and crown jobs, because a failed cap and crown often means the flue tile beneath has taken on water and needs resurfacing. HeatShield ceramic resurfacing is a solution most general handymen can’t perform, and it extends the life of the flue without a full reline when the damage is caught early. Whether you have Gelco, Famco, Olympia Chimney, or any other make, we can help.
Signs You Need Chimney Cap & Crown Right Now
- Rust stains on the chimney or roof. A rusted cap is a cap that’s leaking, and the stains down the masonry are where that water has been running. It’s not cosmetic; the metal is thinning and the cap will fail outright before long.
- Water coming into the firebox. If you’re seeing dampness or a stain on the ceiling near the chimney after rain, the cap or the crown is the likely culprit. Water in the flue corrodes the damper and the flue tile, and that’s where the serious costs start.
- Cracks wider than a hairline in the crown. Surface cracking is normal; a crack you can fit a credit card into is not. It means the crown isn’t shedding water anymore, and the brick below it is soaking it up.
- Birds, squirrels, or nests in the flue. If you’re hearing scratching in the chimney or find debris in the firebox, the cap’s mesh is gone or the cap is missing. An animal in the flue is a real blockage hazard, and the blockage needs clearing before you burn again.
- Pieces of mortar on the roof or in the yard. Falling crown material means the crown is breaking down. Those pieces need to be cleared and the crown repaired before the next heavy rain moves more masonry off the top.
Our Chimney Cap & Crown Process – Step by Step
- 1
Book with a flat price. You call, we confirm what you’re seeing, and we book a visit with a flat price for the sweep and inspection quoted before we come. The written estimate that follows sets the final price, and you’ll see that number before any work is scheduled.
- 2
Inspect the top and the flue. Our technician climbs to the chimney top, checks the cap, crown, and flue tile, and photographs what’s up there. We also look down the flue from the roof when it’s safe to do so, so we’re not guessing from the firebox end.
- 3
Camera inspection and photo report. We run a camera down the flue and hand you a photo report of what we found. You see the crack, the missing cap, or the failed crown yourself, which is how you know the recommendation is honest.
- 4
Approve the written estimate. We explain what needs doing now, what can safely wait, and the cost of each. We don’t recommend a repair we can’t show you on camera, and if the crown can be coated rather than rebuilt, we’ll say so.
- 5
Install and clean up. We install the new cap or crown using professional-grade products, seal the top against water, and clear every piece of old mortar and debris from the roof and yard. You get a final walk-through and photos of the finished work.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Garden Oaks?
A typical cap installation in Garden Oaks runs $180 – $450 depending on the flue size and whether you pick a stainless or a copper unit. A multi-flue cap for a wider chimney top is usually in the $280 – $650 range. Crown coating, which is the less expensive option when the crown is sound, typically runs $250 – $600; a full crown rebuild runs $350 – $900 depending on the chimney footprint and the height of the scaffold needed.
A few things move the price. Custom caps cost more than stock sizes because the unit is fabricated to fit. Copper costs more than stainless and lasts longer. Access matters too: a chimney on a steep roof or a tall stack takes more setup time than one on a low single-story home.
The best way to avoid overpaying is to get a written estimate that separates the cap, the crown work, and any flue repair so you can see each item. We tell you what your chimney actually needs, and if the crown can safely wait, we’ll tell you that too. Our chimney inspection process starts with a camera sweep, includes a photo report, and the estimate itself is free. Call (844) 299-4971 for an exact quote.
Chimney Cap & Crown Near Garden Oaks – Our Service Area
We work across Garden Oaks and the surrounding neighborhoods, including Oak Forest, The Heights, Acres Homes, Spring Branch, and Spring Valley Village. We also cover River Oaks, Montrose, and Uptown further south, plus Hedwig Village, Hunters Creek Village, and Aldine. Wherever you’re located in this part of town, we schedule cap and crown work by appointment with fast dispatch from 7am to 7pm, and we offer chimney cap & crown for homeowners just east of us in Oak Forest as well.
Serving Garden Oaks, TX – Our Local Coverage Area
We serve Garden Oaks and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Garden Oaks
Chimney cap and crown work covers the two pieces that protect the top of your chimney from weather: the crown is the concrete slab on the chimney top that sheds water away from the brick, and the cap is the fitted metal cover on the flue that keeps rain, animals, and debris out. We repair or rebuild crowns and install, replace, or custom-fit caps. Both jobs are about keeping water out of the masonry and flue, which is the single biggest cause of chimney damage in Garden Oaks homes.
Most cap installations take about an hour. Crown coating typically takes one visit and a few hours, and a crown rebuild usually takes a couple of hours depending on the footprint. We bring the cap or crown materials with us based on the measurements taken at the estimate, so there’s no second visit. If the flue underneath needs resurfacing with HeatShield, we’ll quote that separately and book it once you approve.
Cap installation typically runs $180 – $450 and crown coating runs $250 – $600, with a full crown rebuild in the $350 – $900 range. What you pay depends on the flue size, the material, and how much access the roof allows. The written estimate sets the final price. Call (844) 299-4971 for an exact quote – estimates are free.
Yes. We install, replace, and service Gelco and Famco caps and know where those products wear out over time. We also work with Olympia Chimney for custom-fit caps and with HeatShield for any flue resurfacing the job needs. Whether you have one of those brands or any other make, we can help.
Yes, we offer same-day service when the schedule allows, and we confirm the time when you call. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (844) 299-4971 and we’ll lock in a time.
Yes, we back our cap and crown work with a satisfaction guarantee. If something isn’t right with the installation or the seal, we come back and make it right. We use professional-grade materials from Gelco, Famco, and Olympia Chimney because the material quality is what makes a warranty worth having in the first place.
You don’t need to do much beyond making sure we can get to the fireplace and, if you can, clearing a path to the chimney on the roof side. Move any furniture or decor away from the firebox so we can inspect it cleanly. If you have a gas insert, turn it off before we arrive. We bring the drop cloths and the tools, and we take every bit of debris away with us.
Schedule Your Chimney Cap & Crown Service in Garden Oaks Today
If your cap is missing, rusted, or you’re not sure the crown is doing its job, call us. Our technicians have up to 14 years of experience, and we install caps and crowns from the same professional-trade brands chimney professionals specify. The estimate is free and there’s no obligation. Call (844) 299-4971. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’ll book you in and take care of chimney cap & crown work from the firebox to the cap.
Written by the team at Chimney Sweep Garden Oaks.